Waydoo Evo | How to Setup and Best Practices for Safe and Smooth Operation

The Waydoo Flyer One Evo eFoil offers an exhilarating experience on the water, blending the excitement of surfing with the innovation of electric propulsion. This guide will walk you through the steps necessary to assemble and operate your Waydoo Evo eFoil safely and efficiently.

Follow these detailed instructions to ensure a smooth and enjoyable ride.

Checking and Preparing the Battery

Step 1: Inspect the Battery and Locks

1. Battery Rotary Locks: Ensure that the rotary locks are in place and the pins are correctly aligned in the grooves before installation.
2. Sensor and DC Ports: Check the sensor ports and DC ports for any water or debris. Clean and dry them if necessary to prevent any damage.

Step 2: Installing the Battery

1. Handling the Battery: Lift the Powerlight battery with both hands and place it carefully into the battery compartment.
2. Securing the Battery: Press the battery downward to ensure it is fully inserted into the board.
3. Securing with Hex Key: Remove the L-shaped hex key from the rubber plug and insert the plug into the board.
4. Tightening the Battery: Use the latch from the remote wrist strap to press the two round rotary locks on the Powerlight battery. Rotate them clockwise about 90° to tighten them.

Preparing the Propulsion Unit and Mast

Step 1: Prepping the Propulsion Unit

1. Removing Protective Sleeves: Remove the two protective sleeves from the propulsion unit.
2. Applying Grease: Apply a suitable amount of grease on the sealing ring according to the actual situation.

Step 2: Attaching the Mast

1. Removing Protective Sleeves from the Mast: Remove the three protective sleeves on the mast.
2. Inserting the Mast: Slowly insert the mast vertically downward onto the propulsion unit. Move the mast slightly left and right to make it easier to fit into place.
3. Securing the Mast: Fix and tighten it with two M6x20 bolts.

Step 3: Attaching the Mast to the Board

1. Inserting the Mast into the Board: Turn the board over and insert the mast vertically into the mast mounting part.
2. Securing the Mast: Ensure the mast is installed correctly and tighten it with two M6x20 bolts.

Installing the Wings

Step 1: Front Wing Installation

1. Attaching the Front Wing: Place the front wing on the propulsion unit mounting bracket.
2. Securing the Front Wing: Use three M6x35 bolts and tighten them with an L-shaped hex key.

Step 2: Tail Wing Installation

1. Attaching the Tail Wing: Attach the tail wing to the propulsion unit mounting bracket.
2. Securing the Tail Wing: Use two M6x20 bolts and tighten them with an L-shaped hex key.

Operating the Waydoo Evo eFoil

Step 1: Powering On the Remote and Board

1. Preparing the Remote: Wrap the remote wrist strap around your wrist.
2. Turning on the Remote: Long press the power button on the remote for 3 seconds to turn it on.
3. Powering on the Board: Use the magnet on the remote to long tap on the battery power button for 3 seconds to turn on the board.

Step 2: Connecting the Remote to the Board

1. Bluetooth Connection: Press and hold the power button and the speed gear button on the remote simultaneously for 2 seconds to open the Bluetooth connection management interface.
2. Selecting the Board: A list of available boards will be displayed. Use the plus and minus speed gear buttons to select the board to connect.
3. Confirming Connection: Press the trigger to confirm. The Powerlight battery will pop out a confirmation tip. Tap the battery power button to confirm if the connection is successful. The remote display will return to the homepage automatically.

Step 3: Adjusting and Operating

1. Unlocking the Remote: Hold the remote's minus button for 2 seconds to unlock it.
2. Adjusting the Gear: Use the plus and minus buttons on the remote to adjust the gear.

Step 4: Powering Off

1. Turning Off the Board: Use the magnet on the remote to long tap on the battery power button for 3 seconds to turn off the board.
2. Turning Off the Remote: Long press the power button on the remote for 3 seconds to turn it off.

Disassembling the Waydoo Evo eFoil

Step 1: Unlocking and Removing the Battery

1. Unlocking the Battery: Rotate the two battery rotary locks counterclockwise by 90° to unlock them.
2. Removing the Battery: Remove the rubber plug and press the unlock switch with your finger while lifting the Powerlight battery up with both hands slowly.

By following these detailed steps, you can ensure the proper assembly, operation, and disassembly of your Waydoo Evo eFoil, allowing for an optimal experience on the water. Happy eFoiling!